Skip to main content
Amphenol 112424

Amphenol 112424 BNC Jack, 50 Ohm, 4 GHz, Panel Mount

MPN 112424
Active

Amphenol BNC jack, female socket, 50 Ohm, 4 GHz, 500 V, panel mount bulkhead, solder cup, gold centre contact, nickel body.

$3.2100 Ref. price · indicative, final on quote
Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for stock & sourcing questions
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent supplier — new & surplus connector stock· Listing updated Aug 2026

Specifications

112424 key specifications
ParameterValue
MountingPanel Mount
Connector typeJack, Female Socket
Fastening typeBayonet Lock
Voltage rating500 V
Frequency - max4 GHz
Mounting featureBulkhead - Rear Side Nut
Body materialBrass
Housing colorSilver
Dielectric materialPolyoxymethylene (POM) Acetal
Center contact materialPhosphor Bronze
PackageBag
FeaturesExtended Insulation

All specifications

112424 additional specifications
ParameterValue
Includes4 pcs - 1 Connector, 1 Lockwasher, 1 Nut, 1 Solder Tag
Impedance50 Ohms
Body finishNickel
Mating cycles500
Insertion loss0.2dB
Number of ports1
Shield terminationSolder Tag
Contact terminationSolder Cup
Center contact platingGold

Product details

The 112424: The 500 V voltage rating and 500 mating cycles put it in the standard-duty range for test equipment, instrumentation, and RF distribution panels where the connector gets swapped a few times a week, not a few times a day.

Mounting Hardware and What Ships in the Bag

The bag includes four pieces: the connector itself, a lockwasher, a hex nut, and a solder tag. The lockwasher sits between the nut and the panel to keep the nut from backing off under vibration — skip it and the connector can rotate when you mate or unmate the cable. The solder tag gives you a dedicated point for the shield connection; run a wire from the tag to the chassis ground rather than relying on the nut-to-panel contact alone. The extended insulation feature (listed on the spec line) means the dielectric — polyoxymethylene (POM) acetal — extends past the mating face, which adds creepage distance for the 500 V rating in humid environments.

Signal Path: Impedance, Frequency, and Insertion Loss

The 4 GHz ceiling covers the L-band and S-band; above that the insertion loss climbs past the 0.2 dB mark listed in the spec. That 0.2 dB figure is at the lower end of the band — expect it to rise as you approach 4 GHz, but the spec holds across the full range. The gold-plated phosphor bronze centre contact keeps the signal path corrosion-free through the 500-cycle life; the nickel-plated brass body handles the shield return.

The 112431 is the closest functional peer — same BNC jack, same 50 Ohm / 4 GHz / 500 V ratings, same bulkhead mount with rear nut. The difference is the dielectric: the 112424 uses POM acetal, while the 112431 uses PTFE. PTFE holds its dielectric constant tighter across temperature and frequency, so the 112431 is the better choice if the connector sits in a thermal cycling environment or runs near the 4 GHz ceiling. The 112424's POM dielectric is adequate for room-temperature bench work and general-purpose RF distribution. The 112404 is a solder-termination variant without the extended insulation feature — same ratings, different dielectric, no solder tag included.

MPN
112424