Skip to main content
TE Connectivity AMP Connectors 2406866-1

TE Connectivity 2406866-1 SMPM Receptacle, 40 GHz, RG-405

MPN 2406866-1
Active

TE Connectivity SMPM blind-mate receptacle, female socket, 50 Ohm, DC to 40 GHz, snap-on coupling, solder termination, RG-405 (.086" semi-rigid) cable group, gold-plated brass body, 1 port, free-hanging right-angle mount.

$31.2900 Ref. price · indicative, final on quote
Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for stock & sourcing questions
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent supplier — new & surplus connector stock· Listing updated Aug 2026

Specifications

2406866-1 key specifications
ParameterValue
SeriesBlind-Mate Coaxial
MountingFree Hanging (In-Line), Right Angle
Connector typeReceptacle, Female Socket
Fastening typeSnap-On
Voltage rating175 V
Frequency - max40 GHz
Cable groupRG-405 (.086 Semi Rigid)
Operating temperature-40°C~125°C
Body materialBrass
Housing colorGold
Dielectric materialPolytetrafluoroethylene (PTFE)
Center contact materialBeryllium Copper

All specifications

2406866-1 additional specifications
ParameterValue
PackageBag
Impedance50Ohm
Body finishGold
Mating cycles100
Number of ports1
Shield terminationSolder
Contact terminationSolder
Center contact platingGold

Product details

40 GHz SMPM Blind-Mate Receptacle for RG-405 Semi-Rigid Cable

The TE Connectivity 2406866-1 is an SMPM-series blind-mate coaxial receptacle, a female socket designed for DC to 40 GHz signal paths. The gold-plated brass body and beryllium copper center contact with gold plating keep the insertion loss low across the full millimeter-wave band.

What the 40 GHz Rating Means for the Signal Path

The 40 GHz maximum frequency sets the usable bandwidth for this SMPM receptacle — it covers the entire Ku, K, and Ka bands, plus the lower end of the millimeter-wave spectrum. At 40 GHz, the 50 Ohm impedance tolerance and the PTFE dielectric control the phase stability through the launch. The 175 V voltage rating is a dielectric-withstand ceiling, not a continuous operating limit; at these frequencies the signal voltage is a fraction of that. The 100 mating cycles are typical for a blind-mate connector in a backplane or module interface — the snap-on coupling wears the detent over time, so this isn't a test-port connector for daily connect/disconnect.

Cable and Termination — RG-405 Only, Solder Both Ends

This receptacle is designed for RG-405 (.086" semi-rigid) coax — the cable group is specified in the part number and the center contact bore, shield diameter, and dielectric support are sized for that cable.

Comparing the 2406866-1 to the 1057230-1 OSP Peer

Both use snap-on coupling, solder termination, and gold-plated beryllium copper center contacts, and both are rated for RG-405 (.085" semi-rigid) cable. The critical difference is bandwidth: the 2406866-1 SMPM receptacle is rated to 40 GHz, while the 1057230-1 OSP jack stops at 22 GHz. If your signal path stays below 22 GHz, the 1057230-1 is a viable alternative with a stainless body that resists corrosion better than brass. Above 22 GHz, the 2406866-1 is the only choice between these two.

MPN
2406866-1