Skip to main content
87185-112HLF — Amphenol product photo

Amphenol BERGSTIK II 87185-112HLF Header, 12 Pos

MPN87185-112HLF
Active

Amphenol BERGSTIK II 87185-112HLF board-to-board header, unshrouded, single row, 12 positions, 0.100" (2.54 mm) pitch, through-hole solder, rated 5 A, gold or GXT contact finish.

$1.9500Ref. price · indicative, final on quote
StockContact for availability
Lead timeIn Stock wk
MOQ1 pcs
  • New & original stockTraceable channels only — no mixed lots, no re-taped reels.
  • Factory packaging where availableSealed reels, trays and bags; cut quantities always stated on the quote.
  • Photo-verified countsEvery line counted and photographed before the box closes.
  • PayPal buyer protectionPay by T/T, PayPal or Payoneer — card payments covered end to end.

Specifications

87185-112HLF Technical Specifications
ParameterValue
SeriesBERGSTIK® II
GenderMale Pin
Mounting typeThrough Hole
Connector typeHeader
Fastening typePush-Pull
Voltage rating110V
Current rating5A
Contact materialPhosphor Bronze
Insulation colorBlack
Insulation height0.100\" (2.54mm)
Material flammability ratingUL94 V-0
StyleBoard to Board
PackageBag
ShroudingUnshrouded
TerminationSolder
Contact shapeSquare
Rows1
Pitch0.100\" (2.54mm)
Positions12
Contact length - post0.095\" (2.41mm)
Overall contact length1.238\" (31.45mm)
Contact finish - matingGold or Gold, GXT™
Contact length - mating1.043\" (26.49mm)
Contact finish thickness - mating30.0µin (0.76µm)

Product details

The Amphenol BERGSTIK II 87185-112HLF is a 12-position, single-row, unshrouded male pin header on the standard 0.100" (2.54 mm) pitch. It is a board-to-board interconnect — the pins mate with a matching receptacle housing, typically a BergStik or similar 0.100" pitch socket strip. The through-hole solder termination and square pins make it a direct fit for breadboard, perfboard, or any PCB laid out on 0.100" centers. Rated 5 A per circuit with a 110 V voltage rating, it handles signal and light power duty in prototype, test equipment, and production assemblies where the unshrouded profile keeps the footprint low.

What the key ratings mean for your fit

The 0.100" (2.54 mm) pitch is the classic DIP/breadboard spacing — your PCB footprint matches any standard 0.100" header receptacle or socket strip. The 12 positions are fully loaded, so every pin is present; if your BOM calls for 12 circuits, this is a one-to-one match. The 5 A per circuit rating is per-pin at the rated temperature rise — suitable for signal lines, logic power, and low-current loads, but not a bus-level power rail. The 30.0 µin (0.76 µm) gold or GXT plating on the mating surface gives this header a high cycle life — good for test fixtures, programming jigs, or any application where the connector sees repeated mate/unmate cycles. The unshrouded design means there is no keying or polarization: the mating receptacle must provide its own shroud and the assembler must align the pin row visually.

Mating and termination

This header mates with any standard 0.100" (2.54 mm) pitch receptacle or socket strip — the unshrouded pins insert into the mating housing's shroud. The push-pull fastening means there is no locking latch; the retention comes from the contact interference fit. The through-hole solder termination is a straight post, 0.095" (2.41 mm) long, for soldering into plated through-holes. The overall contact length of 1.238" (31.45 mm) includes a 1.043" (26.49 mm) mating length — the pins extend well above the housing for deep engagement with the receptacle.

Frequently asked questions

What is the pitch of 87185-112HLF?

The pitch is 0.100" (2.54 mm) — the standard breadboard- and DIP-compatible spacing.

What is the current rating of 87185-112HLF?

Rated 5 A per circuit at the stated temperature rise — suitable for signal and light power duty.

Can 87185-112HLF be used with a 2.54 mm header receptacle?

Yes — the 0.100" (2.54 mm) pitch mates with any standard 2.54 mm receptacle or socket strip. The unshrouded pins insert into the mating housing's shroud.